Differences

This shows you the differences between two versions of the page.

--- en:mm-saver:cookbook [2018/09/11 21:15]
bahnfrank65 [2.1 The insertion of own vehicles]
+++ en:mm-saver:cookbook [2018/09/12 09:42] (current)
bahnfrank65 [4 internet links]
@@ Line 84: / Line 84: @@
 When __"Animated locomotive"__ is activated, whether it is a vehicle, which consists of several partial images. These frames must have the following endings: vehicle_name_0, vehicle_name_1, vehicle_name_2, and vehicle_name_3. If it is a vehicle that has single frames, then the __"Change phases to ... pixels (s)"__ must be set. Depending on the vehicle or wheel diameter is a value between about 5 and 15 good. Here is a little try out. Generally speaking, the bigger the wheel, the higher the value. Please also note the program instructions here!
-For __"Picture for right pantograph present"__ is for electric locomotives (only if the __"genus"__ is set to electric locomotive!) Set whether there should be a change of the pantograph depending on the direction of travel, or not, The whole works only if an image file with the extension Bildname_SAR exists. Again, please note the program instructions!
+For __"Picture for right pantograph present"__ is for electric locomotives (only if the __"genus"__ is set to electric locomotive!) Set whether there should be a change of the pantograph depending on the direction of travel, or not, The whole works only if an image file with the extension picturename_SAR exists. Again, please note the program instructions!
 (*) At __"Trains pulled/train selection ..."__ you get into this window ...
@@ Line 125: / Line 125: @@
 ^ GT | Genus / vehicle type | D | Steam locomotive ||
 ^ | | E | Electric loco ||
-^ | | V | D
+^ | | V | Diesel Loco ||
+^ | | DT | Steam railcar ||
+^ | | ET | Electric motor coach ||
+^ | | EA | Battery Power Car | GT = EA |
+^ | | VT | Diesel railcar ||
+^ | | ES | Tram ||
+^ | | VB | Bus ((For all road vehicles)) ||
+^ | | VZ | Two-way vehicle ||
+^ | | X | other ||
+| ** EPOCHE ** | Epoch | 1 |||
+| | | 2 |||
+| | | 3 |||
+| | | 4 || EPOCHE = 4-6 |
+| | | 5 |||
+| | | 6 |||
+^ ULAND | Country of origin | B | Belgium ||
+^ | | FRG | Germany ||
+^ | | GDR | GDR ||
+^ | | CH | Switzerland | ULAND = BN / BLS |
+^ | | F | France | You can also give your own name, |
+^ | | USA | USA | see above |
+^ | | H | Hungary ||
+^ | | ... and others |||
+| ** OL ** | Catenary | J | with catenary | OL = J |
+| | | N | without overhead line ||
+^ OLH | Catenary height | + n | lower than 58 pixels | OLH = 4 equals 54 pixels |
+| ** SAR ** | Picture for right pantograph | J | Image available | SAR = J |
+^ COPIES | Copies | n | maximum number of vehicles | COPIES = 1 |
+| ** DIRECTION ** | Direction of deployment | R | only goes to the right | DIRECTION = R |
+| | | L | only goes to the left ||
+^ RANGIER | Shunting locomotive | J | Use as shunting locomotive possible | RANKER = J |
+| ** FLAGS ** | Accessories | n | Variable | ((A FLAGS = xx can only be inserted with the editor.) The location is:
+''> ...; FLAGS = 1024; SELECTED = 1; {LocoEnd} <'' // Exception the busbar //)) |
+| | Variables can be added \\ | 1 | Train stops and continues \\ (railcar) | FLAGS = 1 |
+| | | 2 | Train stops and continues | FLAGS = 2 |
+| | | 16 | several vehicles in one line \\ (stop) ((The FLAGS = 16 (stop) should not be used) Unfortunately, the program has an error at this point)) | FLAGS = 16 |
+| | | 32 | Busbar | FLAGS = 64 |
+| | | 64 | Color bar for Transrapid | FLAGS = 64 |
+| | | 1024 | Snow for S-plow / \\ S-miller | FLAGS = 1024 |
+^ WZ | Turning | J | Reversible | WZ = J |
+| ** VMAX ** | Maximum speed ||| VMAX = 6 |
+^ VMIN | Minimum speed ||| VMIN = 2 |
+| ** DT ** | Double traction | J | Double traction | DT = J |
+^ PHASE LENGTH | Phasing of animations | n | Number of pixels until the next phase | PHASE LENGTH = 6 |
+| ** ZG ** | Train class | n | Variable ||
+| | Variables can be added | 1 | High-speed trains ||
+| | | 2 | Long-distance traffic ||
+| | | 4 | Regional distributor ||
+| | | 8 | Freight train | ZG = 63 |
+| | | 16 | Private Railways ||
+| | | 32 | other trains ||
+^ TRAIN | Train | | usable with ... | TRAIN = RFI, RFG |
+| ** SELECTED ** || Selection || SELECTED = 1 ((If a vehicle is not selected, not SELECTED = 0, but nothing written down at this point [According to Martin Mayer SELECTED can be written but = 0, but the program itself deletes the entry SELECTED = 1]) ) |
+^ Separator | As a separator, between the individual parameters, is a semicolon (;) to set ||||
+| ** {LocoEnd} ** | End of line ||||
+==== 3.1 Footnotes ====
+) Today usually only "bmp" is used and no more "dib"
+) For all road vehicles
+) A FLAGS = xx can only be inserted with the editor. The place is:
+''> ...; FLAGS = 1024; SELECTED = 1; {LocoEnd} <'' (except the busbar)
+) The FLAGS = 16 (stop) should not be used. The program unfortunately has an error at this point
+) If a vehicle is not selected, not SELECTED = 0, but nothing at this point written down (After
+ Statement by Martin Mayer SELECTED = 0 can be written, but the program itself deletes the entry SELECTED = 1)
+) As a separator, between the individual parameters, a semicolon (;) is set
+===== 4 internet links =====
+The MM railroad saver page: www.mm-eisenbahn.de
+The new railway barrier: http://www.bahnschranke.tt4u.de
+{{mm-saver:mm_cookbook:das_mm-kochbuch_m13b0ffdc.png|}}: http://notepad-plus.sourceforge.net
+{{http://www.just-great-software.com/banners/eppbtnmadesmallorange.png}}: [[http://www.editpadlite.com/]]
+<del>The HP of Pierre Ofzareck: http://www.user-bmp-ini.de</del> //no longer available//
+The HP of Thomas Brian and Martin Voepel: http://voepelm.de
+//[[info@voepelm.de|Martin Voepel]] 2007/05/03 12:21//

Eisenbahn-Bildschirmschoner-Wiki

User Tools

Site Tools

Differences

Page Tools